UDOO NEO BASIC
The most energy-efficient UDOO NEO for your embedded system.
UDOO NEO BASIC is the perfect solution for low power consumption embedded systems.
You can use it as a Headless Device, exploiting USB and Ethernet ports. The board is compatible with most Arduino shields, sensors and actuators. UDOO NEO BASICis also compatible with UDOO Bricks: programmable modules, like the temperature sensor and the barometric sensor, that you can add to make UDOO NEO BASIC even more versatile.
UDOO NEO BASIC can be powered in three ways. You can use:
- A standard 12 volts power supply, we recommend this one;
- A Micro USB cable like the one we have in our USB Kit;
- Any USB battery pack available on the market.
List of Components:
- 1x UDOO NEO BASIC
You can check out our Kickstarter Campaign.
UDOO NEO BASIC is the perfect solution for low power consumption embedded systems.
You can use it as a Headless Device, exploiting USB and Ethernet ports. The board is compatible with most Arduino shields, sensors and actuators. UDOO NEO BASICis also compatible with UDOO Bricks: programmable modules, like the temperature sensor and the barometric sensor, that you can add to make UDOO NEO BASIC even more versatile.
UDOO NEO BASIC can be powered in three ways. You can use:
- A standard 12 volts power supply, we recommend this one;
- A Micro USB cable like the one we have in our USB Kit;
- Any USB battery pack available on the market.
List of Components:
- 1x UDOO NEO BASIC
You can check out our Kickstarter Campaign.
- Additional Information
-
Additional Information
Processor NXP™ i.MX 6SoloX applications processor with an embedded ARM Cortex-A9 core and a Cortex-M4 Core Memory DDR3 512MB Graphics Vivante GC420 Integrated 2D/3D graphics controller Video Interfaces Micro HDMI interface - LVDS interface + touch (I2C signals)
Analog camera connection supporting NTSC and PAL
8-bit parallel camera interface*Mass Storage MicroSD card slot onboard
8-bit SDIO interface*Networking Fast ethernet RJ45 – 10/100Mbps USB 1x USB 2.0 Type A ports
1x USB OTG (micro-AB connector)Audio HDMI audio transmitter
S/PIDF & I2S*Serial Ports 3x UART ports*
2x CAN Bus interfaces*Other Interfaces 8x PWM signals*
3x I2C interface*
1x SPI interface*
6x multiplexable signals*Digital I/O PIns 32 extended GPIOs (A9 dedicated) 22 arduino GPIOs (M4 dedicated) LEDs 1x Green Power Status LED
2x User Configurable LEDs (Red and Orange)Integrated Sensors 1x Sensors Snap-in I2C connector Power Supply 1x DC Micro USB 5V
1x DC Power Jack 6-15V
1x RTC Battery ConnectorOperating Systems Linux UDOObuntu2 (14.04 LTS)
Android Marshmallow 6.0.1Dimensions 89mm x 59mm - 3.50 inch x 2.32 inch Arduino Pinout Arduino-compatible through the standard Arduino Uno layout and compatible with Arduino shields. Digital I/O Pins 32 extended GPIOs (A9 dedicated)
22 Arduino GPIOs (M4 dedicated)Analog I/O Pins 6 available Pins Note *Available on Pin Header - Projects
-
UDOO NEO projects bundles
-
myva-Home (Voice controlled home automation)
My Voice Activated/Controlled Home, Using the Linkit Smart and an Android with easy to use examples and libraries
-
SFAC
A Smart T-shirt designed for athlete and bikers.
-
Home Energy Monitor
A low cost, high performance energy meter for my home.
-
To get started with UDOO NEO follow the link below and discover all the videos and resources to unleash all the power of your NEO.
Get Started NEO
Get Started NEO
UDOO NEO BASIC |
UDOO NEO FULL |
UDOO QUAD |
|
|
|
|
|
| cpu |
NXP™ i.MX 6SoloX applications processor with an embedded ARM Cortex-A9 core and a Cortex-M4 Core
|
NXP™ i.MX 6SoloX applications processor with an embedded ARM Cortex-A9 core and a Cortex-M4 Core
|
NXP i.MX 6 Quad + Atmel SAM3X8E
|
| ram |
DDR3 512MB
|
DDR3 1GB
|
Low Voltage 1GB DDR3
|
| gpu |
Vivante GC420 Integrated 2D/3D graphics controller
|
Vivante GC420 Integrated 2D/3D graphics controller
|
Vivante GC 2000 + Vivante GC 355 + Vivante GC 320
|
Please wait... 
Shipments are managed from Italy by UPS Courier. 
